qmk_firmware/layouts/community/ortho_4x12/drashna/config.h
Drashna Jaelre e3a21348c3
[Keymap] Drashna's Hardware Features Experimentations (#6920)
* Change RGBLight pin for Planck Light

Move it to A0, so that the SPI? pins are available for BT hackery

* Add QMK DFU bootloader info

* Add Solenoid

* Disable annoying white LED on bottom

* Enable Solenoid on Corne

* Remove bounds for animations

* Increase debounce for Ergodox EZ to reduce repeat key issues

* Set swap hands key to be a hold-tap key

This way, it's not ANNOYING and doesn't swap the hands inteniontally

* Move MT Alt in Corne keymap

* Re-Add fine tuned control of secrets

* Squash mods to single row

* Add LRA settings to haptic feedback settings for Rev6

* Fix issue with non-Planck EZ keymaps

* Add 40 Percent Nano with Analog Joystick

* Add Collide39 keymap

* Fix OLED printing to be more flavorful

* Fix up Iris GamePad and come cleanup

* Expand OLED char map further

* Add modded characters to keylogger

* Here be dragons

Co-Authored-By: noroadsleft <18669334+noroadsleft@users.noreply.github.com>

* Fix up rules for community layouts

* Some more OLED tweaks

* Add mod mask check function

* Change QMK DFU Audio pin to be correct

* Use manual STM config instead of CTPC for Collide 39
2019-10-16 13:11:22 -07:00

131 lines
3.8 KiB
C

#pragma once
#if defined(RGBLIGHT_ENABLE) && !defined(RGBLED_NUM)
# define RGB_DI_PIN A0
# define RGBLED_NUM 13 // Number of LEDs
# define RGBLIGHT_ANIMATIONS
# define RGBLIGHT_HUE_STEP 12
# define RGBLIGHT_SAT_STEP 12
# define RGBLIGHT_VAL_STEP 12
# define RGBLIGHT_EFFECT_KNIGHT_LENGTH 2
# define RGBLIGHT_EFFECT_SNAKE_LENGTH 2
# ifdef RGB_MATRIX_ENABLE
# define RGBLIGHT_DISABLE_KEYCODES
# endif
#endif // RGBLIGHT_ENABLE
#ifdef RGB_MATRIX_ENABLE
# define RGB_MATRIX_KEYPRESSES // reacts to keypresses (will slow down matrix scan by a lot)
// #define RGB_MATRIX_KEYRELEASES // reacts to keyreleases (not recommened)
# define RGB_MATRIX_FRAMEBUFFER_EFFECTS
// #define RGB_DISABLE_AFTER_TIMEOUT 0 // number of ticks to wait until disabling effects
// #define RGB_MATRIX_MAXIMUM_BRIGHTNESS 200 // limits maximum brightness of LEDs to 200 out of 255. If not defined maximum brightness is set to 255
# define RGB_DISABLE_WHEN_USB_SUSPENDED true // turn off effects when suspended
# undef RGB_MATRIX_LED_PROCESS_LIMIT
# undef RGB_MATRIX_LED_FLUSH_LIMIT
#endif
#if defined(KEYBOARD_lets_split_rev2)
# define USE_SERIAL
# undef USE_I2C
# define EE_HANDS
#endif
#if !defined(KEYBOARD_planck_light)
# ifdef RGBLIGHT_ENABLE
# define NO_MUSIC_MODE
# endif // RGBLIGHT_ENABLE
#else
# undef QMK_ESC_OUTPUT
# define QMK_ESC_OUTPUT E6 // usually COL
# undef QMK_ESC_INPUT
# define QMK_ESC_INPUT B0 // usually ROW
# undef QMK_LED
# define QMK_LED D6
# undef QMK_SPEAKER
# define QMK_SPEAKER B5
# define SOLENOID_PIN A1
#endif // KEYBOARD_planck_light
#if defined(KEYBOARD_planck)
# undef PRODUCT
# if defined(KEYBOARD_planck_light)
# define PRODUCT Drashna Hacked RGB Beacon(Planck Light)
# elif defined(KEYBOARD_planck_rev6)
# define PRODUCT Drashna Hacked Planck Rev6
# elif defined(KEYBOARD_planck_ez)
# define PRODUCT Drashna Hacked Planck EZ
# endif
#endif
/*
* MIDI options
*/
/* Prevent use of disabled MIDI features in the keymap */
//#define MIDI_ENABLE_STRICT 1
/* enable basic MIDI features:
- MIDI notes can be sent when in Music mode is on
*/
// #define MIDI_BASIC
/* enable advanced MIDI features:
- MIDI notes can be added to the keymap
- Octave shift and transpose
- Virtual sustain, portamento, and modulation wheel
- etc.
*/
//#define MIDI_ADVANCED
/* override number of MIDI tone keycodes (each octave adds 12 keycodes and allocates 12 bytes) */
//#define MIDI_TONE_KEYCODE_OCTAVES 2
#define FB_ERM_LRA 1 /* For ERM:0 or LRA:1*/
#define FB_BRAKEFACTOR 6 /* For 1x:0, 2x:1, 3x:2, 4x:3, 6x:4, 8x:5, 16x:6, Disable Braking:7 */
#define FB_LOOPGAIN 1 /* For Low:0, Medium:1, High:2, Very High:3 */
/* default 3V ERM vibration motor voltage and library*/
#if FB_ERM_LRA == 0
#define RATED_VOLTAGE 3
#define V_RMS 2.3
#define V_PEAK 3.30
/* Library Selection */
#define LIB_SELECTION 4 /* For Empty:0' TS2200 library A to D:1-5, LRA Library: 6 */
/* default 2V LRA voltage and library */
#elif FB_ERM_LRA == 1
#define RATED_VOLTAGE 2
#define V_RMS 2.0
#define V_PEAK 2.85
#define F_LRA 200
/* Library Selection */
#define LIB_SELECTION 6 /* For Empty:0' TS2200 library A to D:1-5, LRA Library: 6 */
#endif
/* Control 1 register settings */
#define DRIVE_TIME 25
#define AC_COUPLE 0
#define STARTUP_BOOST 1
/* Control 2 Settings */
#define BIDIR_INPUT 1
#define BRAKE_STAB 1 /* Loopgain is reduced when braking is almost complete to improve stability */
#define SAMPLE_TIME 3
#define BLANKING_TIME 1
#define IDISS_TIME 1
/* Control 3 settings */
#define NG_THRESH 2
#define ERM_OPEN_LOOP 1
#define SUPPLY_COMP_DIS 0
#define DATA_FORMAT_RTO 0
#define LRA_DRIVE_MODE 0
#define N_PWM_ANALOG 0
#define LRA_OPEN_LOOP 0
/* Control 4 settings */
#define ZC_DET_TIME 0
#define AUTO_CAL_TIME 3