Consolidate udev rules into a single file
This commit is contained in:
fauxpark
parent
f079dd90ed
commit
a21e487fbc
@ -13,65 +13,68 @@ An example of using `sudo`, when your controller is ATMega32u4:
|
||||
|
||||
or just:
|
||||
|
||||
$ sudo make <keyboard>:<keymap>:dfu
|
||||
$ sudo make <keyboard>:<keymap>:flash
|
||||
|
||||
Note that running `make` with `sudo` is generally ***not*** a good idea, and you should use one of the former methods, if possible.
|
||||
|
||||
### Linux `udev` Rules
|
||||
On Linux, you'll need proper privileges to access the MCU. You can either use
|
||||
`sudo` when flashing firmware, or place these files in `/etc/udev/rules.d/`. Once added run the following:
|
||||
```console
|
||||
|
||||
On Linux, you'll need proper privileges to communicate with the bootloader device. You can either use `sudo` when flashing firmware, or place this file in `/etc/udev/rules.d/`:
|
||||
|
||||
**/etc/udev/rules.d/50-qmk.rules:**
|
||||
```
|
||||
# Atmel DFU
|
||||
# ATmega16U2
|
||||
SUBSYSTEMS=="usb", ATTRS{idVendor}=="03EB", ATTRS{idProduct}=="2FEF", TAG+="uaccess", RUN{builtin}+="uaccess"
|
||||
# ATmega32U2
|
||||
SUBSYSTEMS=="usb", ATTRS{idVendor}=="03EB", ATTRS{idProduct}=="2FF0", TAG+="uaccess", RUN{builtin}+="uaccess"
|
||||
# ATmega16U4
|
||||
SUBSYSTEMS=="usb", ATTRS{idVendor}=="03EB", ATTRS{idProduct}=="2FF3", TAG+="uaccess", RUN{builtin}+="uaccess"
|
||||
# ATmega32U4
|
||||
SUBSYSTEMS=="usb", ATTRS{idVendor}=="03EB", ATTRS{idProduct}=="2FF4", TAG+="uaccess", RUN{builtin}+="uaccess"
|
||||
# AT90USB128
|
||||
SUBSYSTEMS=="usb", ATTRS{idVendor}=="03EB", ATTRS{idProduct}=="2FF9", TAG+="uaccess", RUN{builtin}+="uaccess"
|
||||
# AT90USB128
|
||||
SUBSYSTEMS=="usb", ATTRS{idVendor}=="03EB", ATTRS{idProduct}=="2FFB", TAG+="uaccess", RUN{builtin}+="uaccess"
|
||||
|
||||
# Input Club
|
||||
SUBSYSTEMS=="usb", ATTRS{idVendor}=="1C11", ATTRS{idProduct}=="B007", TAG+="uaccess", RUN{builtin}+="uaccess"
|
||||
|
||||
# STM32duino
|
||||
SUBSYSTEMS=="usb", ATTRS{idVendor}=="1EAF", ATTRS{idProduct}=="0003", TAG+="uaccess", RUN{builtin}+="uaccess"
|
||||
# STM32 DFU
|
||||
SUBSYSTEMS=="usb", ATTRS{idVendor}=="0483", ATTRS{idProduct}=="DF11", TAG+="uaccess", RUN{builtin}+="uaccess"
|
||||
|
||||
# BootloadHID
|
||||
SUBSYSTEMS=="usb", ATTRS{idVendor}=="16C0", ATTRS{idProduct}=="05DF", TAG+="uaccess", RUN{builtin}+="uaccess"
|
||||
|
||||
# USBAspLoader
|
||||
SUBSYSTEMS=="usb", ATTRS{idVendor}=="16C0", ATTRS{idProduct}=="05DC", TAG+="uaccess", RUN{builtin}+="uaccess"
|
||||
|
||||
# ModemManager should ignore the following devices
|
||||
# Atmel SAM-BA (Massdrop)
|
||||
SUBSYSTEMS=="usb", ATTRS{idVendor}=="03EB" ATTRS{idProduct}=="6124" TAG+="uaccess", RUN{builtin}+="uaccess", ENV{ID_MM_DEVICE_IGNORE}="1"
|
||||
# Caterina
|
||||
SUBSYSTEMS=="usb", ATTRS{idVendor}=="2A03" TAG+="uaccess", RUN{builtin}+="uaccess", ENV{ID_MM_DEVICE_IGNORE}="1"
|
||||
SUBSYSTEMS=="usb", ATTRS{idVendor}=="2341" TAG+="uaccess", RUN{builtin}+="uaccess", ENV{ID_MM_DEVICE_IGNORE}="1"
|
||||
SUBSYSTEMS=="usb", ATTRS{idVendor}=="1B4F" TAG+="uaccess", RUN{builtin}+="uaccess", ENV{ID_MM_DEVICE_IGNORE}="1"
|
||||
```
|
||||
|
||||
Once added, run the following:
|
||||
|
||||
```
|
||||
sudo udevadm control --reload-rules
|
||||
sudo udevadm trigger
|
||||
```
|
||||
|
||||
**/etc/udev/rules.d/50-atmel-dfu.rules:**
|
||||
```
|
||||
# Atmel ATMega32U4
|
||||
SUBSYSTEMS=="usb", ATTRS{idVendor}=="03eb", ATTRS{idProduct}=="2ff4", TAG+="uaccess", RUN{builtin}+="uaccess"
|
||||
# Atmel USBKEY AT90USB1287
|
||||
SUBSYSTEMS=="usb", ATTRS{idVendor}=="03eb", ATTRS{idProduct}=="2ffb", TAG+="uaccess", RUN{builtin}+="uaccess"
|
||||
# Atmel ATMega32U2
|
||||
SUBSYSTEMS=="usb", ATTRS{idVendor}=="03eb", ATTRS{idProduct}=="2ff0", TAG+="uaccess", RUN{builtin}+="uaccess"
|
||||
```
|
||||
|
||||
**/etc/udev/rules.d/54-input-club-keyboard.rules:**
|
||||
**Note:** With older versions of ModemManager (< 1.12), filtering only works when not in strict mode. The following commands can update that setting:
|
||||
|
||||
```
|
||||
# Input Club keyboard bootloader
|
||||
SUBSYSTEMS=="usb", ATTRS{idVendor}=="1c11", ATTRS{idProduct}=="b007", TAG+="uaccess", RUN{builtin}+="uaccess"
|
||||
```
|
||||
|
||||
**/etc/udev/rules.d/55-caterina.rules:**
|
||||
```
|
||||
# ModemManager should ignore the following devices
|
||||
SUBSYSTEMS=="usb", ATTRS{idVendor}=="2a03", ATTRS{idProduct}=="0036", TAG+="uaccess", RUN{builtin}+="uaccess", ENV{ID_MM_DEVICE_IGNORE}="1"
|
||||
SUBSYSTEMS=="usb", ATTRS{idVendor}=="2341", ATTRS{idProduct}=="0036", TAG+="uaccess", RUN{builtin}+="uaccess", ENV{ID_MM_DEVICE_IGNORE}="1"
|
||||
SUBSYSTEMS=="usb", ATTRS{idVendor}=="1b4f", ATTRS{idProduct}=="9205", TAG+="uaccess", RUN{builtin}+="uaccess", ENV{ID_MM_DEVICE_IGNORE}="1"
|
||||
SUBSYSTEMS=="usb", ATTRS{idVendor}=="1b4f", ATTRS{idProduct}=="9203", TAG+="uaccess", RUN{builtin}+="uaccess", ENV{ID_MM_DEVICE_IGNORE}="1"
|
||||
```
|
||||
|
||||
**Note:** With older (before 1.12) ModemManager, filtering only works when not in strict mode, the following commands can update that settings:
|
||||
```console
|
||||
printf '[Service]\nExecStart=\nExecStart=/usr/sbin/ModemManager --filter-policy=default' | sudo tee /etc/systemd/system/ModemManager.service.d/policy.conf
|
||||
sudo systemctl daemon-reload
|
||||
sudo systemctl restart ModemManager
|
||||
```
|
||||
|
||||
**/etc/udev/rules.d/56-dfu-util.rules:**
|
||||
```
|
||||
# stm32duino
|
||||
SUBSYSTEMS=="usb", ATTRS{idVendor}=="1eaf", ATTRS{idProduct}=="0003", TAG+="uaccess", RUN{builtin}+="uaccess"
|
||||
# Generic stm32
|
||||
SUBSYSTEMS=="usb", ATTRS{idVendor}=="0483", ATTRS{idProduct}=="df11", TAG+="uaccess", RUN{builtin}+="uaccess"
|
||||
```
|
||||
|
||||
**/etc/udev/rules.d/57-bootloadhid.rules:**
|
||||
```
|
||||
# bootloadHID
|
||||
SUBSYSTEMS=="usb", ATTRS{idVendor}=="16c0", ATTRS{idProduct}=="05df", TAG+="uaccess", RUN{builtin}+="uaccess"
|
||||
```
|
||||
|
||||
### Serial device is not detected in bootloader mode on Linux
|
||||
Make sure your kernel has appropriate support for your device. If your device uses USB ACM, such as
|
||||
Pro Micro (Atmega32u4), make sure to include `CONFIG_USB_ACM=y`. Other devices may require `USB_SERIAL` and any of its sub options.
|
||||
@ -96,46 +99,6 @@ You can buy a really unique VID:PID here. I don't think you need this for person
|
||||
- http://www.obdev.at/products/vusb/license.html
|
||||
- http://www.mcselec.com/index.php?page=shop.product_details&flypage=shop.flypage&product_id=92&option=com_phpshop&Itemid=1
|
||||
|
||||
## BOOTLOADER_SIZE for AVR
|
||||
Note that Teensy2.0++ bootloader size is 2048byte. Some Makefiles may have wrong comment.
|
||||
|
||||
```
|
||||
# Boot Section Size in *bytes*
|
||||
# Teensy halfKay 512
|
||||
# Teensy++ halfKay 2048
|
||||
# Atmel DFU loader 4096 (TMK Alt Controller)
|
||||
# LUFA bootloader 4096
|
||||
# USBaspLoader 2048
|
||||
OPT_DEFS += -DBOOTLOADER_SIZE=2048
|
||||
```
|
||||
|
||||
## `avr-gcc: internal compiler error: Abort trap: 6 (program cc1)` on MacOS
|
||||
|
||||
This is an issue with updating on brew, causing symlinks that avr-gcc depend on getting mangled.
|
||||
|
||||
The solution is to remove and reinstall all affected modules.
|
||||
|
||||
```
|
||||
brew rm avr-gcc avr-gcc@8 dfu-programmer dfu-util gcc-arm-none-eabi arm-gcc-bin@8 avrdude qmk
|
||||
brew install qmk/qmk/qmk
|
||||
brew link --force avr-gcc@8
|
||||
brew link --force arm-gcc-bin@8
|
||||
```
|
||||
|
||||
### `avr-gcc` and LUFA
|
||||
|
||||
If you updated your `avr-gcc` and you see errors involving LUFA, for example:
|
||||
|
||||
`lib/lufa/LUFA/Drivers/USB/Class/Device/AudioClassDevice.h:380:5: error: 'const' attribute on function returning 'void'`
|
||||
|
||||
For now, you need to rollback `avr-gcc` to 8 in Homebrew.
|
||||
|
||||
```
|
||||
brew uninstall --force avr-gcc
|
||||
brew install avr-gcc@8
|
||||
brew link --force avr-gcc@8
|
||||
```
|
||||
|
||||
### I just flashed my keyboard and it does nothing/keypresses don't register - it's also ARM (rev6 planck, clueboard 60, hs60v2, etc...) (Feb 2019)
|
||||
Due to how EEPROM works on ARM based chips, saved settings may no longer be valid. This affects the default layers, and *may*, under certain circumstances we are still figuring out, make the keyboard unusable. Resetting the EEPROM will correct this.
|
||||
|
||||
|
||||
Loading…
Reference in New Issue
Block a user